Skip to content

Scream Canister Lamp and Shade

Advertising
Share
Add to
Make
Advertising
?
Creation quality: 5.0/5 (1 vote)
Evaluation of members on the printability, utility, level of detail, etc.
  • 1.9k views
  • 10 likes
  • 2 downloads
License
3D design format
STL Folder details Close
  • 1 SL Base 60 hrs.stl
  • 10 SL Gauge Frame 11hrs.stl
  • 11 SL Positive.stl
  • 12 SL Negative.stl
  • 13 SL Screw.stl
  • 14 SL Gauge Marker 5hrs.stl
  • 15 SL Gauge Bar 3hrs.stl
  • 16 SL Gauge Back 6hrs.stl
  • 17 SL Thin Pin 1hr.stl
  • 18 SL jumbo linking nut 5hrs.stl
  • 19 SL Washer.stl
  • 2 SL Junction 37 hrs.stl
  • 20 SL Long Bolt 2hrs.stl
  • 21 SL Gear Brace 1hr.stl
  • 22 SL Switch bar brace 4hrs.stl
  • 23 SL Gear Tension 1 hr.stl
  • 24 SL Top Pipe 5hrs.stl
  • 3 SL Main 90 hrs.stl
  • 4 SL Top Band 21 hrs.stl
  • 5 SL Lid 52hrs.stl
  • 6 SL handle 3 hrs.stl
  • 7 SL Round Gear 3hrs.stl
  • 8 SL Straight Gear 3hrs.stl
  • 9 SL Switch Bar 1hr.stl
  • Back Corner Left.stl
  • Back Corner Right.stl
  • Door Back Trim.stl
  • Door Back1.stl
  • Door Back2.stl
  • Door Hole trim.stl
  • Door Hole1.stl
  • Door Hole2.stl
  • Door Left.stl
  • Door Right.stl
  • Front Corner Left.stl
  • Front Corner Right.stl
  • Monster1 Inverted.stl
  • Monster2 Inverted.stl
  • Top Ring 1.stl
  • Top Ring 2.stl
  • monster1.stl
  • monster2.stl
  • shade bones 1.stl
  • shade bones 2.stl
  • shade bones 3.stl
  • shade bones 4.stl
  • shade bones inner.stl
  • shade bones outer.stl

Learn more about the formats
Publication date 2022-06-26 at 04:46
Design number 765592
brassopey

brassopey

3D printer file info

3D model description

This is my rendition of the Scream Canister from Monsters Inc reimagined as a lamp. The red scream level indicator is actually the dimmer select and power on off. By raising the red scream level indicator to full the top, the bulb will be at full brightness and by lowering the indicator it will dim the bulb until it fully shuts off.

3D printing settings

I printed this in PLA+
Each piece can be printed in its corresponding color, so no paint is needed.
Please use supports and re-orientate parts to get the best results for your printer.

23 SL GEAR TENSION will need to be heated and bent to interact with the main gear properly. This can be done with a heat gun / hot hair dryer / or very carefully with a lighter.

Also this will require a general working knowledge of electronics and lamp building. Please build to your own level and safety.

You will need a rotary dimmer switch that engages, on, off and dims only by rotation. a push button switch will not work with this.

Other miscellaneous lamp parts can be purchased in lamp kits from various retailers and or an existing donor lamp can be cannibalized for parts.

This is just for the body parts and gearing no electronics or wiring instructions are in this download.

To Print the shade standard settings as above but the lithophane should be printed at 100% infill. There are 2 copies of the lithophane a standard and an inverted depending if you want to show a flat or textured surface when the lamp is off.

Each of the shade pieces should be printed with their largest flat printed flush (laying) on the print bed.

The 4 corners will print standing upright.

The shade will need to be glued together. I personally like Weld-on-4 for PLA prints but others can be used.

The inner shade (shade bones and bones inner and outer) will all be glued together and seperate from the main shade. The main shade slides down so each "bone" rests in a corner and the angle holds it together.

Tags

Advertising

Issue with this design? Report a problem.
Check out similar designs

Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your banner blocker (AdBlock, …) and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon.

  • DONATE: If you want, you can make a donation via Ko-Fi πŸ’œ.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!

Sharing and downloading on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not accountable to any investor or brand. Almost all of the site's revenues are paid back to the platform's makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.
Currency: USD
Cults.
100% secure payment by credit card, PayPal, Apple Pay, Google Pay, etc.
View all payment options.