The lamp is made to not have to use brackets, but if you want you can put brackets on the base up to the height of 1-3cm, but be careful, that the brackets are never made in the center where is the hole to put the electronics but it will be impossible to put it in the middle of the print, for this use the tool Cura de bloqueador de soporte that is in the left bar below and then click on the model to display the square, then enlarge the square of blocking support and center it, I leave image. Whether you use brackets or not, my advice is to use lacquer for the base, I make them without brackets because with lacquer is enough so that it does not detach from the base.
I use cura with two different printers, one is the anycubic Mega pro and the other an Artillery Genius Pro, For the printing parameters I use with 0,4mm nozzle for lithophanes I leave the curaprofile files for you to download.
On how to put the electronics I leave images to guide you, I put it in motion so that there are no lines on the ball, but you can do it pausing until you get looseness, watch out that when you put the electronics with the hot silicone you can tilt, so be careful and if it tilts put it back to stand and so on until the silicone hardens. You can also use high viscosity cyanoacrylate with activator, but that's up to each one.
The link to buy the electronics is as follows:
https://es.aliexpress.com/item/1005003069067412.html?gatewayAdapt=glo2esp&spm=a2g0o.order_list.0.0.21ef194dNHceyI
For the wooden base they also sell the kit with the base, but I prefer to print it, I leave you the link and also the files in case you prefer to print it yourself:
https://es.aliexpress.com/item/1005003257853473.html?spm=a2g0o.detail.1000014.3.7ed04978HCkTqM&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.40050.274735.0&scm_id=1007.40050.274735.0&scm-url=1007.40050.274735.0&pvid=fea26db1-4db3-4bac-b20d-9f96013c7027&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.40050.274735.0,pvid:fea26db1-4db3-4bac-b20d-9f96013c7027,tpp_buckets:668%232846%238116%232002&pdp_ext_f=%257B%2522sku_id%2522%253A%252212000024886767066%2522%252C%2522sceneId%2522%253A%252230050%2522%257D&pdp_pi=-1%253B6.76%253B-1%253B-1%2540salePrice%253BEUR%253Brecommend-recommend
I use cura with two different printers, one is the anycubic Mega pro and the other an Artillery Genius Pro, For the print parameters I use with 0,4mm nozzle for lithophanes I leave the curaprofile files for you to download.
On how to put the electronics I leave images to guide you, I put it in motion so that there are no lines on the ball, but you can do it pausing until you get looseness, watch out that when you put the electronics with hot silicone you can tilt, so be careful and if it tilts put it back to stand and so until the silicone hardens.
The link to buy the electronics is as follows:
https://es.aliexpress.com/item/1005003069067412.html?gatewayAdapt=glo2esp&spm=a2g0o.order_list.0.0.21ef194dNHceyI
For the wooden base they also sell the kit with the base, but I prefer to print it, I leave you the link and also the files in case you prefer to print it yourself:
https://es.aliexpress.com/item/1005003257853473.html?spm=a2g0o.detail.1000014.3.7ed04978HCkTqM&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.40050.274735.0&scm_id=1007.40050.274735.0&scm-url=1007.40050.274735.0&pvid=fea26db1-4db3-4bac-b20d-9f96013c7027&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.40050.274735.0,pvid:fea26db1-4db3-4bac-b20d-9f96013c7027,tpp_buckets:668%232846%238116%232002&pdp_ext_f=%257B%2522sku_id%2522%253A%252212000024886767066%2522%252C%2522sceneId%2522%253A%252230050%2522%257D&pdp_pi=-1%253B6.76%253B-1%253B-1%2540salePrice%253BEUR%253Brecommend-recommend