Skip to content

HO Scale LORAM RGS1 Rail Grinder Track Vacuum Maintenance of Way

1SQ.jpg HO Scale LORAM RGS1 Rail Grinder Track Vacuum Maintenance of Way
EXPLODED-VIEW.jpg HO Scale LORAM RGS1 Rail Grinder Track Vacuum Maintenance of Way
2SQ.jpg HO Scale LORAM RGS1 Rail Grinder Track Vacuum Maintenance of Way
3SQ.jpg HO Scale LORAM RGS1 Rail Grinder Track Vacuum Maintenance of Way
4SQ.jpg HO Scale LORAM RGS1 Rail Grinder Track Vacuum Maintenance of Way
5SQ.jpg HO Scale LORAM RGS1 Rail Grinder Track Vacuum Maintenance of Way
6SQ.jpg HO Scale LORAM RGS1 Rail Grinder Track Vacuum Maintenance of Way
7SQ.jpg HO Scale LORAM RGS1 Rail Grinder Track Vacuum Maintenance of Way
8SQ.jpg HO Scale LORAM RGS1 Rail Grinder Track Vacuum Maintenance of Way
9SQ.jpg HO Scale LORAM RGS1 Rail Grinder Track Vacuum Maintenance of Way
Advertising
Share
Add to
Make
Advertising
?
Creation quality: 5.0/5 (2 votes)
Evaluation of members on the printability, utility, level of detail, etc.
  • 15k views
  • 32 likes
  • 27 downloads
  • 2 collections
  • 1 comment
License
3D design format
ZIP Folder details Close
  • HOVACFILES.zip
    • 01 END DBL TAB INS.stl
    • 02 END DBL TAB INS.stl
    • 2 END SGL TAB INS.stl
    • ANEMOMETER.stl
    • BATTERY COMPARTMENT.stl
    • BATTERY ROOF-LID.stl
    • DUST FILTER FRAME.stl
    • ENG BODY FRT SHELL.stl
    • ENG BODY RR SHELL.stl
    • ENG CAB FRT SIREN-SPKR.stl
    • ENG CAB GRILLE.stl
    • ENG CAB MID SIREN-SPKR.stl
    • ENG CAB SHELL.stl
    • ENG CAB WIPER 1.stl
    • ENG CAB WIPER 2.stl
    • ENG CAB WIPER 3.stl
    • ENG CAB WNDW BEZEL - 2.stl
    • ENG FRONT LEFT RAILING.stl
    • ENG FRONT RIGHT RAILING.stl
    • ENG PLOW - COUPLER COVER.stl
    • ENG RAILING 1.stl
    • ENG RAILING 2.stl
    • ENG RAILING 3.stl
    • ENG RAILING 4.stl
    • ENG RR BODY LATCH.stl
    • ENG RR BODY VENT LG - 2.stl
    • ENG RR BODY VENT SM - 2.stl
    • ENG RR LATCH COVER PLATE.stl
    • ENGINE CHASSIS - DECK - PART I.stl
    • ENGINE CHASSIS - DECK - PART II.stl
    • ENGINE-GRINDER LINK.stl
    • FRT BODY VENTS 1.stl
    • FRT BODY VENTS 2.stl
    • FRT BODY VENTS 3.stl
    • FUEL TANK - BLOWER HOUSING.stl
    • GRDR ROOF VENT-MOTOR.stl
    • GRINDER BODY - FRONT.stl
    • GRINDER BODY - REAR.stl
    • GRINDER CAB GRILLE.stl
    • GRINDER CAB REAR WINDOW.stl
    • GRINDER CAB SHELL.stl
    • GRINDER CAB SIDE WINDOWS - 2.stl
    • GRINDER CAB WIPER 1.stl
    • GRINDER CAB WIPER 2.stl
    • GRINDER CAB WIPER 3.stl
    • GRINDER CHASSIS - DECK PART I.stl
    • GRINDER CHASSIS - DECK PART II.stl
    • GRINDER CHASSIS - LEFT PANEL.stl
    • GRINDER CHASSIS - RIGHT PANEL.stl
    • GRINDER PLOW - COUPLER COVER.stl
    • GRINDER RAILING 1.stl
    • GRINDER RAILING 2.stl
    • GRINDER SHROUD 1.stl
    • GRINDER SHROUD 2.stl
    • GRINDER SHROUD PEGS - 3.stl
    • GRINDER TRUCK NOZZLES - 4.stl
    • HOSE REELS AND TANK.stl
    • LEFT PANEL - ENGINE CHASSIS.stl
    • MID RAILING 1.stl
    • MID RAILING 2.stl
    • MOTOR MOUNT.stl
    • PULL TAB - 2.stl
    • RADIAL FAN.stl
    • REAR ENG BODY TAB.stl
    • RIGHT PANEL - ENGINE CHASSIS.stl
    • ROOF AC UNIT - 5.stl
    • ROOF STROBE - 4.stl
    • SWITCH LINK.stl
    • TOOL BOXES.stl
    • TRUCK BASE PLATE.stl
    • TRUCK LEFT FACE PLATE - FRONT.stl
    • TRUCK LEFT FACE PLATE - REAR.stl
    • TRUCK MAIN FRAME - FRONT.stl
    • TRUCK MAIN FRAME - REAR.stl
    • TRUCK RIGHT FACE PLATE - FRONT.stl
    • TRUCK RIGHT FACE PLATE - REAR.stl

Learn more about the formats
Publication date 2021-12-27 at 20:55
Design number 593872
FentressImagineering

FentressImagineering

3D printer file info

3D model description

This is a WORKING track vacuum in HO scale that uses 4 AA batteries to maintain your track. It has been successfully run on track radii down to 18 inches, but runs best at 22 inches and up. It is modeled after the LORAM Rail Grinding System, a 2-unit rail grinder for short runs of track, crossings, and points/turnouts. Specifically, this model depicts the RGS1 unit (LMIX-404).

The chassis has no motive power of its own and relies on a locomotive for traction. This model is designed to use 4 new or surplus Athearn 42" locomotive axles ("Blue Box") along with two standard 33" freight trucks (Athearn, Atlas, Kadee, etc.). The coupler boxes will work with Kadee Magematic, Athearn, Bachmann, or even legacy X2F couplers.

This battery-powered model uses a hidden slide dual pole, dual throw switch (Slide DPDT) that is actuated by sliding the front engine cab rooftop air conditioner back and forth. When turned on, the track fan beneath the engine section of the model pulls dust and debris such as loose ballast into a removable compartment. This compartment is released by sliding back the rooftop exhaust stack and pivoting upwards. This is very similar to a handheld vacuum (i.e. "Dustbuster"). The air filter is made from 2 plies of used fabric softener dryer sheets sewn onto the removeable frame. While the filter media is removable, it should not be necessary to replace for a long time. Just dump out the dirt and debris.

The grinder section of the model houses the battery compartment which holds four (4) AA batteries. AAs are easily found anywhere. The battery compartment lid is removable and uses both a slight interference fit and gravity to hold it in place. Markings on the inside of the compartment denote the orientation of the battery cells and two pull straps (optional) aid in battery removal. Brass strips are used at the ends to form terminals and to complete the circuit. Two small L-shaped terminals are used at the end towards the front/vacuum/engine section and one large V-shaped terminal is employed at the rear. The terminal sections are removable and facilitate soldering wires to the terminals prior to installation. Wiring snakes through the chassis in both units and employs an optional mini connector between the two.

This model can be printed in either filament or resin. It has been successfully printed using silver PLA on a Prusament Mini+ using a 0.25 mm nozzle and a 0.07 mm layer height. The model is broken up into a large number of pieces to get the proper orientation for the highest possible resolution. Assembly is best accomplished using Plastruct Plastic Weld and/or non-fogging cyanoacrylate (CA) glue such as Bob Smith Super Gold +. Canopy glue works well for adding windows.

The non-printed parts required for this model are readily available at little to no cost. They include:
-Four AA batteries (Alkaline or NiMH rechargeable)
-One Slide DPDT Switch (Radio Shack 2750403 or equivalent)
-One 6 Volt pancake motor (RF-300C-11440) commonly found in DVD or CD players
-Several 2-56 x 3/16" slotted machine screws or metric close equivalents
-One spring from a ball point pen for the "Dustbuster" bin release latch
-Two Kadee Magnematic or other NMRA-pattern couplers
-Clear and or/tinted plastic sheet for cab windows (e.g. styrene, blow mold packaging, thin film sheets, etc.)
-Two 1-72 x 1/8" slotted machine screws for couplers or metric close equivalents

The attached ZIP folder contains 76 individual STL files. This is essentially a 3-D printed version of a model kit.

ENJOY!

3D printing settings

Prusament (Czech Republic) or Atomic (USA) PLA
0.25 mm nozzle at 195-215 deg. Celsius
0.07 mm layer height
60 degree Celsius heated bed temperature

Categories

Designs β€Ί Various β€Ί Dioramas

Tags

Advertising

Issue with this design? Report a problem.

Would you like to support Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 3 people, therefore it is very simple to support us to maintain the activity and create future developments. Here are 4 solutions accessible to all:

  • ADVERTISING: Disable your banner blocker (AdBlock, …) and click on our banner ads.

  • AFFILIATION: Make your purchases online by clicking on our affiliate links here Amazon.

  • DONATE: If you want, you can make a donation via Ko-Fi πŸ’œ.

  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!

Sharing and downloading on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not accountable to any investor or brand. Almost all of the site's revenues are paid back to the platform's makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.
Currency: USD
Cults.
100% secure payment by credit card, PayPal, Apple Pay, Google Pay, etc.
View all payment options.