Messina 1347 organizers

Organizers for Messina 1347 board game. Quick game set up and comfort during the play. Covers prevent components from falling out during the storage. Theme cutouts decorate lids. Holders for Workshop, Quarantine and Wagon tiles fit the game board precisely.

The set contains: Resources organizer, Hex organizer + Divider, Citizen organizer, Player's component organizer, Workshop organizer, Quarantine&Wagon organizer, Boat organizer, Docking tray, Solo container and 2 Collective organizers (accommodating smaller containers).

1. RESOURCES ORGANIZER: A circular organizer with 8 sections dedicated for: coins (in value 1, 3 and 5), fire tokens (plain and major), plague cubes (+ round counter), lumber and rat tokens. Rounded bottom facilitate component draw. In the middle there is a shelf adjusted to Population wheel. The container is covered by a push-in lid. Indentations in the lid facilitate pushing it out.
2. HEX ORGANIZER: Hexagonal map tiles are kept here. To separate different map tiles use a Hex Divider (A for 2 players, A for 4 players, A no matter how many players, B and C). Sloped back wall and indentations facilitate taking tile out. The design of the organizer allows using no infill. This organizer is as high as it can be to fit the game box so no lid is required. It must be placed only on players' boards in the box. A diagonal cut on one side is required so the organizer doesn't interfere with the main game board stored in the box next to it.
3. CITIZEN ORGANIZER: 3 types of Citizen tokens are accommodated here: Nun, Craftsman and Aristocrat. Rounded bottom facilitate the draw. The organizer is adjusted to its location in the game box - it stands next to Hex organizer.
4. PLAYER'S COMPONENT ORGANIZER: All components of one player are accommodated here. There are three separate sections for: 3 starting Lieutenants, 3 Overseers and Repopulation tiles. The rest components are all together in the largest section. Well adjusted recesses and indentations facilitate taking items out.
5. WORKSHOP ORGANIZER: 2 of such organizers should be 3d printed to keep era I and II tiles separately. There are 3 sections for 3 types of Workshops. Indentations facilitate taking tile out. This organizer can be easily attached to the Quarantine&Wagon organizer. Together they fit the game board precisely.
6. QUARANTINE&WAGON ORGANIZER: All sections are adjusted to the game board tile arrangement. Indentations facilitate taking tile out. Simple joints enable attaching this organizer to the Workshop organizer before the play.
7. BOAT ORGANIZER: A neat organizer for Boat tiles. Boats of value 1, 2 and 3 are separated by section walls. Sloped back and section walls and indentations facilitate the draw.
8. DOCKING TRAY: Simple container for Docking tiles. Sloped bottom facilitate the draw.
9. SOLO CONTAINER: A container for Solo game tiles. Sloped back wall and indentations facilitate the draw. Serration prevent tiles from sliding down.
10. COLLECTIVE ORGANIZER 1: In my previous version of organizers for Messina 1347 there was a lot of small containers that were uneasy to store. So I designed Collective organizers to provide a more friendly layout inside the game box. Collective organizer 1 accommodates: Boat organizer, Docking tray and Solo container. Sections are larger than these containers, so its easy to pick them up. It is also adjusted to the citizen organizer, so it fits above it in the game box.
11. COLLECTIVE ORGANIZER 2: Quarantine&Wagon organizer, Harbor hexes and Priority tile are accommodated here. Indentations facilitate picking them up. It fits the game box well next to Player's component organizers.

All organizers fit the game box and provide quick game setup. However it's not an insert. Lids prevent components from falling out during the storage. A lot of decorative skull cutouts are introduced to more enjoy the game ;)

Some photos in higher resolution on instagram:
The set, organizers closed and open
Chosen organizers
Game set up for 3 players
Unpacking

All organizers were 3Dprinted on Prusa MK4 (with Input Shaper):
- in PLA (F3D Gold Pearl),
- No support is needed,
- Infill 10-15% gyroid/rectilinear.
Note1: I use slightly changed default Print settings "0.15mm SPEED MK4" in PrusaSlicer.
Note2: Lids and guides are adjusted to 0.15 mm layer height.
Note3: 0.2 mm layer height was set only for: Resources lid, Hex container and Hex Divider.
Note4: 0% infill was set only for Hex container.
Note5: Monotonic lines as a top fill for lids (as default).

Printing Time (for one organizer of each kind):
2h52' - Resources organizer, container
1h38' - Resources organizer, lid
1h12' - Hex organizer
16' - Hex Divider, x4
1h51' - Citizen organizer, container
55' - Citizen organizer, lid
1h3' - Player's component organizer, container, x4
27' - Player's component organizer, lid, x4
1h16 - Workshop organizer, container, x2
47' - Workshop organizer, lid, x2
1h5' - Quarantine&Wagon organizer, container
13' - Quarantine&Wagon organizer, lid long
11' - Quarantine&Wagon organizer, lid short
33' - Boat organizer
25 - Docking tray
24' - Solo container
1h25' - Collective organizer 1, container
1h8' - Collective organizer 1, lid
2h30' - Collective organizer 2, container
1h35' - Collective organizer 2, lid