organiser with grid by h3li0

h3li0

Household>Office

Print Profile(4)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

two plates · 0.2mm layer, 2 walls, 10% infill

Designer

8.9 h

2 plates

4.8(23)

single plate · 0.2mm layer, 2 walls, 10% infill

Designer

8.7 h

1 plate

4.8(27)

0.2mm layer, 2 walls, 10% infill - Optimized for the A1 mini

6.2 h

2 plates

5.0(6)

0.2mm layer, 2 walls, 10% infill

1.9 h

1 plate

5.0(3)

Boost

350

645

820

356

Released

Description

organiser with grid pattern and removable separator

created in fusion 360

photos show printed in black matte pla and brick red petg-cf

0.20mm layer height
10% adaptive cubic infill

dimensions > x: 200mm · y: 100mm · z: 110mm

including two print profiles:

two plates, for different colours / materials like seen on the photos
single plate, for same colour / material

note > the separator is a tight fit, with small tolerance, if your printer / filament struggle with smaller tolerances, reduce the scale of the separator in bambu studio by 0.5~1%

commercial licence membership available on my patreon

buy me a coffee

note: all photos uploaded are of the actual printed model, taken inside a lightbox or in home studio

Comment & Rating (74)

@3DP0

Print Profile

two plates · 0.2mm layer, 2 walls, 10% infill

(Edited)

Bed Adhesion Issue:Because the sides are chamfered from the bottom AND the top, it leaves the corners to come up over the course of the print which results in over extrusion of the corners. once the print is done, the corners have risen up a quarter to half mil in comparison to the center point of the top of the print. This makes for an uneven structure and the divider doesn’t work as intended as a result.

The designer has replied

@h3li0

sorry to hear about the adhesion issues, however the chamfer does not cause problems for me, i recommend either giving your plate a thorough wash or use 3D LAC (this thing is magic :) )

@3DP0

Replying to @h3li0 :

It’s ok, thanks for your reply :) It’s not so much the bed adhesion, it’s that the corners are up off the bed, thus have nothing to stick to. it’s more the design imo. what’s this you speak of btw, some kind of glue? Sorry I’m rather new to all this. thanks for the help!

@h3li0

indeed it’s adhesion, having the corners at an angle doesn’t mean it warps, from the photos you show it seems like it really did lift the flat side on one of the corners. 3D Lac is an adhesive spray, comes in a can (some people use air spray, but I find this better) it works really great! never have any adhesion issues with it :)

(Edited)

@wvcont

Print Profile

single plate · 0.2mm layer, 2 walls, 10% infill

imprimi em 80% do tamanho original pois era o tamanho que precisava. Tudo perfeito. obrigado

The designer has replied

@h3li0

ficou com um esquema de cor interessante, que filamento e?

@actionman007

Print Profile

0.2mm layer, 2 walls, 10% infill

Good profile, fast print.

@CustomPrinting

Print Profile

two plates · 0.2mm layer, 2 walls, 10% infill

I got a perfect print. Great job to the designer 👏

@user_1227002010

Print Profile

two plates · 0.2mm layer, 2 walls, 10% infill

Very clean model and an easy print.

@user_487586135

Print Profile

two plates · 0.2mm layer, 2 walls, 10% infill

Really cool print out of the box. Without any changes it was really good printable. I had a little bit stringing but not so much as with my other printers. I used Charcoal Black Matte and Orange for the print. Really cool design and will take place in our Bathroom as organizer for our Brushes.

(Edited)

The designer has replied

@h3li0

looks great, thanks for sharing

@hengen.jerome

Thx very much for the file, I printed it on my P1S but scaled it to 75%, it was enough for my wife's desk. As you see on the picture I modelized an addon for your design.

(Edited)