Printed With STONG Polycarbonate. Thanks!

Altizure

ABS_V2_split-up model     0.2mm layer, 3 walls, 15% infill, Arachne

Really cool idea. Works great outside of Bambu as well (obviously hehe)

xsynaticc

ABS_V1 (old)   0.1mm layer, 3 walls, 15% infill, Arachne (threshold angle for wall transition = 50°)

GregR

PLA_V2 0.1mm tolerances   0.1mm layer, 3 walls, 15% infill, Arachne

Fredyy

ABS_V2    0.1mm tolerances  0.1mm layer, 3 walls, 15% infill, Arachne

Thank you for the feedback. I uploaded a new profile with higher tolerances and one that features a non-print-in-place model.

3D_Stuff

aramap22

The problem in version 1 is that the top layer can fuse because of over-extrusion caused by the upper layer overlapping with the walls. I fixed this problem in version 2. The walls can stick together lightly, but you can carefully free them by pulling at the joints or bending them in different directions.

JCMoya68

At which point did the pliers break and for what reason? The pliers can 
break at the flexible point if it is squeezed too hard, but this cannot 
be avoided since this part must be thin to remain flexible. Furthermore,
 the pliers should not be squeezed strongly without holding onto 
something, as they cannot fully close.

user_3001130371

Please let me know what went wrong with your print, because without feedback, it's not possible to address issues and improve the design.

jimapp

jacatac

ABS_V2_high tolerances    0.15mm tolerances  0.2mm layer, 3 walls, 15% infill, Arachne

skeubeulse

ABS_V2_P2.PNG

ABS_V2_P3.jpeg

PLA_V2_P2.PNG

PLA_V2.jpeg

pliers_P1_ü.PNG

pliers_P3.jpeg

pliers_P2.jpeg

PLA_V2.webp

plate_1.png

low coolingLow tolerance for a better feeling, but it can fuse together and have to be carefully broken apart!

pliers_P1.webp

pliers_P3.webp

0.1mm layer3 walls15% infillArachne (threshold angle for wall transition = 50°)whithout support10% coolinghigh print temperature

ABS_V2_tolerances_4bee084c-4061-4f13-aeea-123361f9c11c.webp

Improved version for better holding, gripping, and tolerances. The ABS version should be preferred because of its better flexibility.Split-up model (not print in place), clips in place.0.2mm layer3 walls15% infillArachne (threshold angle for wall transition = 50°)whithout support10% coolinghigh print temperature

ABS_V2_tolerances_51b788e8-489b-44c4-97f7-ee707875fa77.webp

Improved version for better holding, gripping, and tolerances. The ABS version should be preferred because of its better flexibility.Higher tolerances, like in V1, to ensure that the parts don't fuse together too much!0.15mm tolerances0.2mm layer3 walls15% infillArachne (threshold angle for wall transition = 50°)whithout support10% coolinghigh print temperature

ABS_V2_P2.webp

ABS_V2.webp

ABS_V2_P3.webp

Improved version for better holding, gripping, and tolerances. The ABS version should be preferred because of its better flexibility.Low tolerance for a better feeling, but it can fuse together and have to be carefully broken apart!0.1mm tolerances0.1mm layer3 walls15% infillArachne (threshold angle for wall transition = 50°)whithout support10% coolinghigh print temperature

Print in place pliers for disconnecting the connections on the X1C to change the hotend assembly. It is printed in ABS+ or PLA. V2: improved, with better grips and a PLA version. NEW: Model with higher tolerances and a non print in place profile for ABS_V2

Print Profile(5)

Description

Comment & Rating (17)

License

Related Models

Protective of diagonal pliers

Long Nose Pliers

IKEA Skadis Small Pliers Holder with a T-Clip

Pliers (Print in place)

disconnect pliers for extruder X1C