Hocus Pocus Book of Spells Arduino Voice Activated Prop

This is a project I undertook for a Halloween 2018 prop to go with my family dress up as the 3 Sanderson Sisters. I used the Sea Lemon tutorial to do a lot of the book design outside of the 3D models used, I did switch the stitches out to real hemp cord instead of puffy paint. I made holes for the stitching using my trusty Weller soldering iron after the paper mache and painting was done and came back in with paint to clean up the burnt areas. I had to alter the animatronic eye design slightly due to space issues fitting the eye close to the opening of the book. Changed files included with this projected. Commercial use not allowed, don't be a thief like RRD.

https://www.youtube.com/watch?v=TtngRH-ttK8

Credits:
Animatronic Eye Mech by sideburn:
https://www.thingiverse.com/thing:319978

Original Snakes, Front Clasp, and Hinge 3D models by Designs by Phil:
http://www.designsbyphil.com/halloween-file-share.html
Check his page out, nice guy that gave me permission to post my changes to his original design here.

Back Claw designed by Colonel Cthulu aka Cha loo loo on VRChat

Hocus Pocus Book of Spells DIY Tutorial by Sea Lemon:
https://www.youtube.com/watch?v=1ikRL2rMqR0

Amazon Nesting Hollow Book Decoration (Used the 13" one, mine was a British Flag version because it was the cheapest at the time at $19):

Original Link: https://www.amazon.com/Bellaa-Decorative-Storage-Designed-Leather/dp/B01GDUJK9C/

Updated Link to new books that may work:
https://www.amazon.com/Bellaa-28052-World-Leather-Brown/dp/B01GDSB6NM/

Elechouse Voice Recognition Module V3:
https://www.elechouse.com/product/speak-recognition-voice-recognition-module-v3/

Need 2 m3x35 bolts with m3 lock nuts and two 10mm x 1mm cylinder magnets to secure latching mechanism.

Files Included:

cornersnake.stl - printed at 0.1 with 20% infill, no supports, 4 needed

spinesnake.stl - printed at 0.1 with 20% infill, no supports, no brim/had to rotate to fit on MK3 bed, 2 needed

frontclasp.stl - printed at 0.1 with 20% infill, supports for the hinge/hole, 1 needed

jewel.stl - printed at 0.1 with 20% infill, no supports, 1 needed in yellow and goes in frontclasp.stl

sidebraid.stl - printed at 0.1 with 20% infill, supports for the hinge/hole, 1 needed

backclaw.stl - printed at 0.1 with 20% infill, supports for the hinge/hole, 1 needed

finger.stl - printed at 0.1 with 20% infill, needs supports/raft, 5 needed

Animatronic Eye File Changes, use advice given in that project for printing:

servobrackflat.stl - cuts off one servo to make room to fit in the book properly

servobracketbackA.stl - if you want to glue the servo mount to the back of the base, so you can choose where to install the other servo. base_42mmB.stl is not needed if you use this file.

base_42mmB.stl - attaches the servobracket that was cut off on the flat to the same place I put it without having to glue servobracketbackA.stl to it. servobracketbackA.stl and base_42mm.stl from the animatronic eye project is not needed if you use this file.

bookofspells.txt - rename bookofspells.ino - a short arduino program using the elechouse voice activation module to look through.