Christmas Doorframe Decor by SaVo3D

SaVo3D

Household>Decor

Print Profile(2)

All

P1P

P1S

X1 Carbon

X1E

No ironing - only for right door corner - 0.2mm layer, 2 walls, 10% infill

Designer

1.1 h

1 plate

4.8(90)

Ironing at toplayer 0.2mm layer, 2 walls, 10% infill

Designer

1.8 h

1 plate

4.8(14)

Boost

278

480

223

702

714

Released

Description

Decoration for your doorframe to welcome christmas.

The model in the printprofile is scaled to 120%. If you download the stl- file you can scale it at your wish. Just scale the Z- height down to ~4mm, this will give you enough stability, more than 4mm Z- height is not necessary.

Make sure you have good bed adhesion before printing!

Best use a smooth plate.

Wash the plate with oil- free soap and then use isopropyl alcohol to clean the print plate.

For excelent adhesion i use a strong hairspray! This will give you a very good bed adhesion! Apply a thin even coat of the hairspray!

Have a look at my newest models:

SaVo3D | Published - MakerWorld

Comment & Rating (223)

@Thomas.frimann

Print Profile

No ironing - only for right door corner - 0.2mm layer, 2 walls, 10% infill

first later could be tighter/better, But from a distance it looks okey. i did run the first 3 layer @ 50% and rest @ 100-166% until the last two layers That i did run @ 50% (pla slik silver from fibrology.)

(Edited)

The designer has replied

@SaVo3D

So you are rating your false filament settings on me? lol, thank you

@Thomas.frimann

Replying to @SaVo3D :

first layer has noting to do with the filament, its the design of the first layer.

@Thomas.frimann

Replying to @SaVo3D :

But for you since its christmas and I did grow to like the decoration i bumped you up. :)

@stuart.w.freema

Print Profile

No ironing - only for right door corner - 0.2mm layer, 2 walls, 10% infill

Really nice thank you.

(Edited)

The designer has replied

@SaVo3D

5 stars would have been nice if you were satisfied 😊

@stuart.w.freema

Replying to @SaVo3D :

Done 😄

(Edited)

@SaVo3D

Replying to @stuart.w.freema :

Thank you kindly! :-)

@Gentleman

Print Profile

No ironing - only for right door corner - 0.2mm layer, 2 walls, 10% infill

sieht echt super aus, ist für die Größe schnell gedruckt, und wenn man die Oberfläche glättet sieht es noch mal eine Ecke schöner aus

The designer has replied

@SaVo3D

Du brauchst die Oberfläche nicht bügeln lassen. Drehe das Model einfach auf die Seite, die auf dem Druckbett liegt. Wenn Du eine glatte Bauplatte hast, dann wird es noch schöner. Also im Prinzip den Druck laufen lassen wie das Druckprofil es vorsieht, dann auf der rechten Türseite anbringen, somit ist die Seite vorne, die auf dem Druckbett gelegen hat.

@Gentleman

Replying to @SaVo3D :

Ich habe die extra geglättet damit ich die beidseitig nutzen kann

(Edited)

@SaVo3D

Replying to @Gentleman :

Ja, daran hatte ich noch nicht gedacht. Auch gut!

(Edited)

@user_1035655657

Print Profile

No ironing - only for right door corner - 0.2mm layer, 2 walls, 10% infill

P1S Inland PLA

The designer has replied

@SaVo3D

thank you kindly

@Lochpatje

Print Profile

No ironing - only for right door corner - 0.2mm layer, 2 walls, 10% infill

it even stays in place without any glue or tape.

The designer has replied

@SaVo3D

thank you kindly and merry christmas

@870shotgunner87

Print Profile

No ironing - only for right door corner - 0.2mm layer, 2 walls, 10% infill

print is beautiful. profile set up beautifully for the filament

(Edited)

The designer has replied

@SaVo3D

Thank you kindly for your nice words!

@breibru

Print Profile

No ironing - only for right door corner - 0.2mm layer, 2 walls, 10% infill

top print

(Edited)

The designer has replied

@SaVo3D

Thank you kindly! The green comes out nice too. Have fun looking at it!

@Picture_it

Print Profile

No ironing - only for right door corner - 0.2mm layer, 2 walls, 10% infill

looks cute! printed well

The designer has replied

@SaVo3D

Thank you kindly! I am happy to hear that :-). You have some nice models too. I will have a look at them!

(Edited)

@Nikoskar2003

Print Profile

No ironing - only for right door corner - 0.2mm layer, 2 walls, 10% infill

Awesome, without any error during print. Fullamwnt used:eSun PLA Black, default settings! Bambu Lab P1S.

The designer has replied

@SaVo3D

Thank you kindly for your feedback! I am glad you liked it! Did you download the stl file and printed it with your own settings? If so, try out the printprofile that i uploaded, it comes out perfect, with the maximum size of the printbed.

(Edited)