New Year Eve 2024 Party horn - No support needed ! by Papadansmaman

Papadansmaman

Hobby & DIY>Music

GIF

Print Profile(3)

All

P1S

P1P

X1 Carbon

X1E

0.16mm layer, 2 walls, 15% infill (Single color - No AMS needed)

Designer

1.7 h

1 plate

4.8(12)

0.16mm layer, 2 walls, 15% infill (2 colors)

Designer

2.2 h

1 plate

4.3(14)

(No 2024 horn) - 0.16mm layer, 2 walls, 15% infill

Designer

1.6 h

1 plate

5.0(2)

Boost

110

239

265

Released

Description

I am delighted to present to you my very first 3D model: my New Year Eve party horn, and it works!

10...9...8...7...6...5...4...3...2...1... Happy New Year!!!!

Make some noise for this new year with this party horn! 2024 will be great!

It's very easy to assemble! There are only 4 pieces. Everything holds together very well, but you can add some glue if you want!

*** ATTENTION ***

Wait for the plate to cool down and bend the build plate very well before removing the noise-making pellet otherwise, you may bend or break the thin strip that consists of a single layer.

*** HOW TO BLOW ***

The only thing to do when blowing into the mouthpiece is to pinch the lips at the tip of the mouthpiece and blow! That's it!

Since it was my very first 3D model, it took me 10 days during the evenings while my child sleeps to create this horn! It may not be the most wow/perfect design, but I am very satisfied! The longest part was creating prototypes through a lot of trial and error because the position and size of the noise pellet, as well as the shapes, significantly influence the operation of the party horn.

Here is a photo of all my attempts:

You can use, sell, and remix without any issues!

Make some noise!

Comment & Rating (46)

@dragonboyuniver

Printing one right now! hoping it goes good ill let you know how it went.

The designer has replied

@Papadansmaman

thank Let me know!!, if you have any idea to improve it, I'm interested. Have fun :)

@Samlzaen

Replying to @Papadansmaman :

can you make one without the 2024 on it

@Papadansmaman

Replying to @Samlzaen :

Of course, I can! Let me few days and I will upload un profile without the 2024

@ionutxp2

Print Profile

0.16mm layer, 2 walls, 15% infill (Single color - No AMS needed)

it makes what it supposed to do

@AquaHaven

Print Profile

(No 2024 horn) - 0.16mm layer, 2 walls, 15% infill

Printed beautifully in PETG on my A1

@Plazman

Came out nice. ASSEMBLY TIP: Don't put the squeaker in upside down or you'll have to inhale to "blow" it! lol p.s. The walls would probably be too thin, but it might be fun to try printing this in "vase mode."

(Edited)

@Babybump2011

Print Profile

0.16mm layer, 2 walls, 15% infill (2 colors)

printed multiple horns all come out good

(Edited)

@rikki703

Print Profile

(No 2024 horn) - 0.16mm layer, 2 walls, 15% infill

@colleenfoley342

Great for everyone. Thank you

(Edited)

The designer has replied

@Papadansmaman

Thank you for your great comment! Happy new year!

@thudson177

Print Profile

0.16mm layer, 2 walls, 15% infill (Single color - No AMS needed)

Printed single color with PLA from the app. upon getting the parts off the plate, the brims caused a little flash that made me have to sand them just to get them to sort of fit. they were very tight. in the mouthpiece there was considerable stringing inside the mouth piece so I worked on that. also this does not sound like the horns used at NYE party but more like an actual horn. all in all good print but more improvement needed for a Nye horn!

The designer has replied

@Papadansmaman

Hello thudson177! Thank you for your very constructive review! It is appreciated! I'm sorry for the problems with the brim, I usually let cool down the plate first and then peel the brim with a good angle. Sometimes it works and sometimes not, in this case I use my deburring tool. I will try to make one sounds like an NYE party horn for next year! Thank you again! Happy new year :)