AMS Lite Numbers by Wojciech Kawa

Wojciech Kawa

3D Printer>3D Printer Parts

Print Profile(8)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 2 walls, 15% infill, Arachne

Designer

37 min

1 plate

4.9(196)

Upside Down Version, 0.2mm layer, 2 walls, 15% infill, Arachne, skirt

Designer

37 min

1 plate

4.9(63)

Bowden Protect, 0.2mm layer, 2 walls, 15% infill

Designer

48 min

1 plate

4.9(60)

Bowden Protect - Upside-Down, 0.2mm layer, 2 walls, 15% infill

Designer

48 min

1 plate

4.9(31)

Click to see more

Boost

364

585

394

1.3 k

1.4 k

Released

Description

My AMS overlay design with slot numbers.
I used gray and white to make the numbers as visible as possible, but you can of course use any color combination.

I designed a version for users who mount their AMS lite on top of an A1 printer (AMS lite Top Mount for A1). link in the image.

Update !

I noticed that some users wanted to protect their Bowden tubes from the excessive wear and tear of tugging, and I thought it might make sense, so I added Bowden tube holders to my earlier design.

The standard version and the version with Bowden tube protection have upside-down versions for people who mount the AMS on the wall or on dedicated stands.

Check the flow ratio before printing. My print has a few flaws, but they are visible only in photos, normally they are almost invisible.

There are individual cases where the print is too tight and cannot be put on without using a lot of force, in which case I suggest printing again with Bambu Studio, increasing the scale a bit, for example 100.5% (the scale setting is always individual depending on how tight it is fit)

Comment & Rating (394)

@RobinDiekmann

Print Profile

0.2mm layer, 2 walls, 15% infill, Arachne

Awesome, just great! Printed on a carbon bed with black and green PLA, looks really good. The fit is absolutely perfect.

@user_1658220205

love the CF look!

(Edited)

@RobinDiekmann

Replying to @user_1658220205 :

Yeah it really makes it pop!

@lmc590

that looks nice, I have that plate but I keep experiencing adgeation problem after a couple of prints, no amount of soap or IPA has helped, have you experienced anything like that, any tips. thanks.

@user_143056145

Great upgrade. Went 3 colors to better see from a distance or from my camera. The fit was just a little tight to the point it was pulling the AMS covers open. I tried sanding the inside to fit but ended up grabbing the heat gun. Warmed the middle of the part just a little and slapped them on. Perfect fit!!

The designer has replied

@WojciechKawa

For me it fits perfectly. I didn't know it could be so tight. The only solution I can think of is to print again, increasing the scale a bit, for example 100.5%.

@Gigagamesguy

Replying to @WojciechKawa :

habe das gleiche Problem, druck war sauber und sehr sauber, ich denke das es nach dem kalt werden sich etwas zusammenzieht, werde das auch mit dem Heißluftfön probieren. Auf der Originale Bampu Platte konnte ich drucken auf der Von Ali mit Struktur ( Habe im Studio auf smooth PEI gestellt) ging es nicht.

@karrasco1985

Print Profile

0.2mm layer, 2 walls, 15% infill, Arachne

Encaja perfectamente, buen diseño

@NAIAD3D

Print Profile

0.2mm layer, 2 walls, 15% infill, Arachne

Great design, fits perfect

@EngravePrinting

really liked this, but is there any modifications in the pipeline to allow for the (Bambu) AMS on top mod? That has the filament guides, which fit within the original numbers.