日本篠笛 Japanese sinobue 八本调子 两节 Two sections
Copyright Claim
日本篠笛 Japanese sinobue 八本调子 两节 Two sections
Boost
40
62
18
Print Profile(2)
0.2mm layer, 6 walls, 25% infill
Designer
3.3 h
1 plate
0.2mm layer, 6 walls, 30% infill - Tough PLA
2.3 h
1 plate
Boost
40
62
18
1
291
82
Released
Description
这是自己设计建模的一款篠笛，八本调子 用拓竹P1SC打印，黑色PETG ECO，0.4喷嘴0.2层高，实心填充打印，单根打印时间3小时15分钟 试吹感觉还可以，音准音色还有很大的提升空间，可以用来吹着玩或者练习指法 长期学习建议购买专业的演奏级篠笛 原创不易，图纸转载请注明出处，谢谢大家
制作及试吹视频在此链接
Comment & Rating (18)
All
Print Profile
0.2mm layer, 6 walls, 30% infill - Tough PLA
easy to print. sounds good too. using this as for practicing before commiting to a proper one. it's really hard to get sound still need practice
(Edited)
0
Reply
Print Profile
0.2mm layer, 6 walls, 25% infill
I had to slow the printing and adjust the supports to stop it from falling over during printing. It sounds beautiful, my mum loves it. Thank you.
0
Reply
Print Profile
0.2mm layer, 6 walls, 30% infill - Tough PLA
(Edited)
Support Issue:The print profile does not work with PLA Silk and I couldn’t get a successful print. The designer recommends using PLA tough instead.
The designer has replied
0
Reply
Boosted
Sorry to hear your print failed. Unfortunately this is not a print profile issue. The profile is meant for Bambu’s tough pla or something similar like hatch boxes’ pro pla. Silk Pla, especially multi color is a much more difficult material to get good adherence, layer bonding etc. Try changing to a different material or atleast adding back supports and further increase the brim size if you are still trying to use silk pla (as an aside that filament color combination is gorgeous, just need a more conservative print profile setup to get it to print properly). Thanks!
(Edited)2
Reply
Thank you for your reply. I have updated my reply (and rating) to help anyone who decides to use PLA Silk. It is 4* for me but Bambu does not allow it as I did not have a successful print. I will try again with different settings. I think this print would look amazing with multicoloured filament.
0
Reply
Nice print. Printed it in green PLA. Thanks for sharing. I'm not a flutist, so I can only get the first four notes to play but I'm sure that's just me. The only thing I changed was I set "seam" to "random" so I didn't get unsightly z-seams.
0
Reply
Print Profile
0.2mm layer, 6 walls, 25% infill
it's a pole with holes that happens to sometimes make a noise.... that doesn't make it a musical instrument
The designer has replied
0
Reply
You should search for the finger chart of the Japanese sinobue instead of complaining here
(Edited)2
Reply
Replying to @user_32806021
the issue is the mouthpiece, it's not formed correctly to make sound. don't be so butthurt about negative feedback.
0
Reply
Replying to @hYPERfOCUS
You can click on this address to watch the audition video which I posted
https://www.bilibili.com/video/BV1WG411f7jZ/?spm_id_from=333.999.0.0&vd_source=eba968106744ff84311976d85d2ae8ae
(Edited)1
Reply
原配置失败了很多次，改成逐件打印，加了巨多底座，长的那一部分打到96%进度时终于倒了。 [哇.jpg]
0
Reply
加了成吨的支撑才打出来
0
Reply
Print Profile
0.2mm layer, 6 walls, 25% infill
print failed twice
0
Reply
Boosted
Try using the Tough PLA Profile instead. The creator's design is great but had issues with the original print profile and the print failing. The two parts would eventually un adhere and fall over. Slowed down the walls, added larger brims inside and out, removed the need for supports and removed the ironing. Used Bambu's Tough PLA and default filament setting instead of petg while shaving a good bit off the print time. Thanks!
0
Reply
Print Profile
0.2mm layer, 6 walls, 30% infill - Tough PLA
My kid loves it. Planning on buying him a real bamboo one now.
0
Reply
Print Profile
0.2mm layer, 6 walls, 30% infill - Tough PLA
Printed pretty well, didn’t expect it to stick to the plate during end, but everything went fine.
0
Reply
Boosted
Nice Model, did use a custom print profile to slow down travel speeds for the inner and outer wall (Outer 112.5 and inner 168.75). Takes a decent bit of practice but once you get the hang of it you can actually feel the instrument vibrate (evidently plastic versions are harder for beginners normally so not surprised a printed model has a decent learning curve as well). More akin to blowing across the top of a bottle vs using something like a recorder. Pretty neat and fun print, took a chance and used pine green Bambu labs Tough pla and it turned out great. Thanks!
Edit: Added the custom print profile for use with Pla+, in this case used Bambu Labs Tough Pla in Pine Green
(Edited)0
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-Share AlikeRelated Models
© 2024 MakerWorld