Adapter for AMS lite Rotary Spool Holder - Yellow / PLA Matte
Copyright Claim
Adapter for AMS lite Rotary Spool Holder - Yellow / PLA Matte
Boost
43
89
19
Print Profile(1)
0.2mm layer, 3 walls, 25% infill
Designer
1.2 h
1 plate
Boost
43
89
19
1
175
59
Released
Description
Hello there,
with this adapter you can install the Bambu Lab “AMS lite Rotary Spool Holder - Version: Yellow” on the the Bambu Lab A1 mini spool holder.
Step 1: Disassembly of spool holder:
1. Press down snap clip with screwdriver
2. Pull out spool holder rod
Step 2: Print adapter
This adapter is printed with Bambu Lab filament PLA Matte Dark Red. The Print profile may needed to be adjusted to your setup / material.
(I'm still a beginner when it comes to 3D printing, so if you have any suggestions for optimization, let me know ;) )
Step 3: Assembly of adapter to spool holder arm
Step 4: Assembly of AMS lite Rotary Spool Holder - Version: Yellow
Link to the part: https://store.bambulab.com/collections/accessories-for-a1-mini/products/ams-lite-rotary-spool-holder?variant=40963660775539
Step 5: Install Filament Spool
Step 6: Cheers!
Comment & Rating (19)
All
Print Profile
0.2mm layer, 3 walls, 25% infill
Works perfectly! I printed it in Bambu PETG Basic (purple!) so it's tough and smooth enough.
I should point out that there's a strange defect in your model which makes an odd spiral composed of little gaps all the way up the shaft. I thought it was just me, then I saw your photos and you have the same defect.
Fortunately it doesn't impact assembly or operation. It works just fine.
Thank you.
The designer has replied
1
Reply
Hi Fraoch, this structure is linked to the seam position. You can change this option in the slicer,with different results. See pictures below. If anyone has a solution to reduce this effect, I'd be happy to hear it.
Cheers!
(Edited)
1
Reply
Replying to @Piecemak3r
You say you're new to 3D printing. Well, not that new! That's a great explanation. I've never seen "seam position - nearest" before, so it stood out. I'm used to seeing seam position - aligned, and I see how that might cause problems with this model, a prominent seam which I've seen on other PETG prints. Maybe the new scarf seam option available in Bambu Studio 1.9.0 and OrcaSlicer 2.0.0 might eliminate all marks altogether, but it's experimental and may require some tinkering.
(Edited)1
Reply
Print Profile
0.2mm layer, 3 walls, 25% infill
good
1
Reply
thank you
(Edited)
1
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 25% infill
perfect fit and very happy with the new solution AMS lite spool, as you suggested
0
Reply
very sturdy. fit perfectly. didn't even need support.
1
Reply
Print Profile
0.2mm layer, 3 walls, 25% infill
The best addition to my mini. No more tangled filament.
1
Reply
Could you possible design some kind of side mount for the P2S that can utilize the Rotary Spool Holder?
1
Reply
Thank you!
i was thinking of doing this myself, excellent 👍🏼
1
Reply
Print Profile
0.2mm layer, 3 walls, 25% infill
This is nice modification, great work!
1
Reply
Well done ! thanks a lot
1
Reply
License
This work is licensed under a
Creative Commons Attribution-NoncommercialRemixes (1)
© 2024 MakerWorld