ESUN Bambu Lab AMS Cardboard Spool Adapter Ring
Copyright Claim
ESUN Bambu Lab AMS Cardboard Spool Adapter Ring
Boost
479
966
1335
Print Profile(5)
0.2mm layer, 2 walls, 15% infill
Designer
21 min
1 plate
Scaled to 100.5% for larger 200.5mm spools
21 min
1 plate
TPU 98.5% Stretch Fit, 0.2mm layer, 2 walls
37 min
1 plate
TPU 0.12mm layer, 2 walls, 85% infill
41 min
1 plate
Click to see more
Boost
479
966
1335
12
3.9 k
8.5 k
Released
Description
DISCLAIMERS:
- Print profiles NOT created by DesignCraft may contain outdated model versions or suboptimal slicer settings. Use at your own risk! I have no control to moderate or remove these third party print profiles.
- This model may not fit all ESUN cardboard spools. Please review the photos and spool measurements before printing.
Description:
This adapter system wraps the edges of an ESUN 1kg 199x62mm cardboard spool in order to:
- provide smooth rotation within a Bambu Lab AMS
- prevent carboard debris from depositing within a Bambu Lab AMS
Features:
- Reusable
- ESUN nameplate for easy identification when reusing
Instructions:
- Measure your spool first to ensure it matches the specified dimensions
- Print this model twice for a single spool
- Affix one spool ring adapter on each side of the ESUN spool
- See attached photos
Considerations:
- Print Material: Please print with a basic PLA or PETG to minimize any shrinkage.
- Too Tight? Too Loose? Cardboard expands with humidity and contracts when dried. A cardboard spool that has absorbed too much moisture may cause the adapters to fit very tight. Placing the spool in a filament dryer, such as the SUNLU S2, for a bit should resolve this. Note, you should not dry the spool with the adapters attached as they can warp in the heat. Keep in mind that after a long drying session the adapters may fit too loose. This should resolve itself shortly as the cardboard reabsorbs some moisture from the air.
- AMS Lid Doesn't Close? All of the spool adapters I make are less than the official AMS spool clearance limit of 202mm, as specified on the official AMS product page, and as tested within my own AMS. However, some people have stated their spools are rubbing against the lid with the adapters attached. It's hard to say what's causing this since I cannot reproduce the issue myself, however, I've created an AMS Lid Riser which allows you to keep your AMS lid closed while providing additional clearance for larger filament spools. It's a quick and easy print which you can find on my profile or directly here: https://makerworld.com/en/models/33133
Comment & Rating (1335)
All
I used the scaled version 100.5% to fit the new larger spool size, but it didn't fit (also the scale was only on X axis in the file) so at the end for me the right scale was 100.6% both X and Y ;) thank you!
The designer has replied
1
Reply
Thank you for sharing your make and providing feedback! May I ask if you've tried to dry the spool? It's often the case the cardboard spool has expanded from humidity. This is very common even with new spools straight out of the packaging. My go-to solution in this case is to dry the spool in a filament dryer for a few hours to remove any excess moisture from the cardboard and apply the adapters afterwards. Please let me know if you have a moment!
0
Reply
Replying to @DesignCraft
Hi, no I didn't try to dry the spool. ;)
0
Reply
Replying to @simon.mary
Thank you for the reply! I usually recommend first trying to dry the spool before scaling the model because scaling up the diameter will make it too large for the stock AMS lid clearance. I do have an AMS Lid Riser linked in the model description if needed. I hope this helps!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
need to keep the lid a little bit open or it will jam
(Edited)
The designer has replied
2
Reply
Thanks for rating!
0
Reply
same issue here...
0
Reply
Print Profile
Right-hand side adapter - 0.2mm layer, 2 walls, 15% infill
does what it supposed to do. thanks!
The designer has replied
2
Reply
Thank you for sharing your make and rating!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
printed well
The designer has replied
1
Reply
Thank you for sharing your make and rating!
0
Reply
Perfect for AMS, Thanks.
The designer has replied
1
Reply
Thank you for sharing your make!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Fits well. Also on Colorfabb spools. Quick and easy print.
(Edited)
The designer has replied
1
Reply
Thank you for sharing your make and rating!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Fast print, minimal PLA, works as advertised.
The designer has replied
1
Reply
Thank you for sharing your make and rating!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
awesome profile. snaps on perfectly to my esun spool! also fits nicely in the AMS.
The designer has replied
1
Reply
Thank you for sharing your make and rating!
(Edited)1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
All esun spools are using this adapter, great print and tight fit
The designer has replied
1
Reply
Awesome! Thank you for sharing your make and rating!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Muy bien
The designer has replied
1
Reply
Thank you for sharing your make and rating!
0
Reply
License
This work is licensed under a Standard Digital File License.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.
© 2024 MakerWorld