Reverse Blade Sword mini ( Samurai Sword) by mail.iou

mail.iou

Toys & Games>Other Toys & Games

GIF

Print Profile(5)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

X1、P1、A1, 0.2mm layer, 2 walls, 15% infill

Designer

3 h

1 plate

4.6(479)

for A1 mini, 0.2mm layer, 2 walls, 15% infill

Designer

3.8 h

1 plate

4.6(127)

*** 2 hours 19 minutes *** 0.28mm layer, 2 walls, 5% recitiliinear

2.5 h

1 plate

4.6(30)

Reduced waste multicolour print

6.7 h

2 plates

5.0(4)

Click to see more

Boost

820

1287

806

4.4 k

5.4 k

Released

Description

update 04/05/2024

If you want a printing method that is easy to maintain, you can consider my redesign:

Reverse Blade Collapsing Katana - Rurouni Kenshin

https://makerworld.com/en/models/414234

update 01/12/2024
This knife is a one-piece printed design. If you are not sure whether the filament you bought can print this work well, you can refer to my new creation "Nichirin Samurai Sword". This work uses a split printing design to facilitate future maintenance and blade replacement.
Nichirin Samurai Sword : https://makerworld.com/en/models/135353

Reverse Blade Sword mini

This is a smaller version of the Reverse Blade Sword, with a total length of about 80cm, suitable for A1 mini printers or people who don’t want to print too much. If you want to experience the full size, please go to https://makerworld.com/en/models/111322

Notice
It is recommended to use PLA+ and Textured PEI Plate for printing.
If the viscosity of the plate of your 3D printer deteriorates, be sure to use glue to increase the grip to prevent the printed part from falling off halfway and wasting filament.

After printing, please remove the support at the end of the knife.

Repair of fallen blades
This work has been printed and verified on P1S, A1, and A1 mini printers and resized. It is currently tested using three materials: Bambu PLA, eSUN PLA+, and eSUN ePLA-Matte.
The blade surface can be freely expanded and contracted without falling off.
However, since PLA material is not resistant to high temperatures, if it is stretched and swung back and forth many times quickly, it will cause the blade to be heated and expand, causing the blade to be thrown out.
At this time, you can repair it with a simple method. Please use a tape with high viscosity that is not easy to fall off, such as Acetate Cloth Tape.
Stick it on the entrance where the blade falls off. The amount of tape can be adjusted to increase or decrease the size of the enlarged hole. Then push the blade down and plug it back into the entrance to repair it.

Comment & Rating (806)

@Dukester

Print Profile

X1、P1、A1, 0.2mm layer, 2 walls, 15% infill

this is the second one i have printed. great model, on par with every paid sword ive printed so far. thanks

The designer has replied

@mail.iou

The color of this filament is very beautiful.

@Dukester

Replying to @mail.iou :

its iSANMATE PLA+ rainbow from amazon.ca

(Edited)

@playps1ok

Print Profile

for A1 mini, 0.2mm layer, 2 walls, 15% infill

very good

The designer has replied

@mail.iou

Thank you for your support.

@mail.iou

Thank you for your support. I have a new creation "Nichirin Samurai Sword". This work uses a split printing design to facilitate future maintenance and blade replacement. Nichirin Samurai Sword: https://makerworld.com/en/models/135353

@StanaP

Print Profile

X1、P1、A1, 0.2mm layer, 2 walls, 15% infill

Thanks, good model.

The designer has replied

@mail.iou

Thank you for your support.

@ok2vvv

Print Profile

X1、P1、A1, 0.2mm layer, 2 walls, 15% infill

Amazing. First time printing remotely over the phone. I came home with the sword ready. At first glance, it opens by itself, holds beautifully and looks good. I'm excited. Thanks a lot for this great model. :)

The designer has replied

@mail.iou

Thank you for your support.

@mail.iou

@colinbooboo09

I don’t know why this is happening. the first time i printed this it was flawless and i used red PETG basic. i wanted another one so i used a blue-gray PETG basic and the first time it did this then i did it again but i used my computer to download it and it did the same thing what is wrong? Also i noticed that the first one i printed that was perfect is bigger by the size of my pinky *Update* I measured out the size of the original one and the one that didn't work. The original one was 22.4cm and the one that didn't work was 21.5cm. I found the original one was 104.5% of the original. So printed it at 104.5% and it was perfect. So I assume that if you are using PETG you have to scale it up like I did because all of the other comments used PLA at the normal size and it was perfect.

(Edited)

The designer has replied

@mail.iou

I'm sorry to give you a bad experience. You can refer to my new creation "Nichirin Samurai Sword". This work uses a split printing design to facilitate future maintenance and blade replacement. Nichirin Samurai Sword：https://makerworld.com/en/models/135353

@jabbaTheHuds

Boosted

here to help I think it could be wet fillement try drying it out

@Bdaley1976

Print Profile

X1、P1、A1, 0.2mm layer, 2 walls, 15% infill

I did nothing other than clicked send to printer, It worked fabulously. My daughter was super super happy. From one of the pictures you can see I used it as a reward for doing her flashcards every day for two weeks. Be careful whipping it open as some pieces may fly out.