The Spiral (assemble in secs) Propeller Launcher Toy by NUKDDD

NUKDDD

Toys & Games>Outdoor Toys

GIF

Print Profile(8)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

Everything you need brim on main handle 0.2mm layer, 2 walls, 6-15% infill

Designer

1.4 h

1 plate

4.7(135)

Improved Stick 0.2mm layer, 2 walls, 15% infill

Designer

19 min

1 plate

4.9(9)

Toroidal Poopeller 0.2mm layer, 2 walls, 15% infill

Designer

27 min

1 plate

5.0(6)

poopeller only 0.2mm layer, 2 walls, 6% infill

Designer

26 min

1 plate

4.8(5)

Click to see more

Boost

370

588

225

1.6 k

1.7 k

Released

Description

please give me a 👍🏻 if you like this, even if you don't download this, it’ll help more people discover this. thanks so much!

Super easy to assemble, from print finish to launching the propeller in literally seconds.

New Toroidal Poopeller now avaible as STL and print profile. If you're turned off by the Poopeller, I have normal ones here. You can stack up to 4 propellers and launch them at the same time! Try it!

This is really about the Spiral Launcher, but have you ever seen shit fly or wondered what it looked like when the shit hits the fan? The faster you pull, the farther it flies. You'd be surprised how THIS SHIT FLIES! I sure was!

Easy to print, no support and no other hardware or complicated assembly to worry about, put the spiral stick in the handle and snap on the cap and you're ready to send some shit flying all around your house and yard and park, etc.

IMPORTANT: I know you're smarter than this, but…Find the arrow on the handle and insert the stick from there, refer to picture #4. Print with a rigid material like PLA plus/tough. Always use safe practices when playing with this. By downloading and playing with this flying toy, you're agreeing to exempt the designer from any personal or property damages or loss you may cause.

How to use after assembly:

Put the poopeller on the spiral stick, upside down works too, maybe even better

Find the small arrow on the handle and insert the rack, face the teeth toward the arrow, put the rack in gently

Point the tip of the handle at the direction you want the projectile to go. But wind will always win, always.

Please be careful the first time, especially indoors, you've been warned.

Unlike other propeller launchers, this one uses a mini version of the spiral from The Fast and Furious Fudge and combines it with the mechanics of an ordinary propeller launcher. As you pull to turn the gears it rotates and pushes it forward, a TRUE launcher, sending this shit high into the sky.

Comment & Rating (225)

@jerem49

Print Profile

Everything you need brim on main handle 0.2mm layer, 2 walls, 6-15% infill

ne fonctionne pas avec moi la tirette semble à avoir trop de jeu et quand on tire rapidement sa saute les cran.

(Edited)

The designer has replied

@NUKDDD

thanks for including the picture, it looks like you need to insert the stick the from the other side, where there’s a tiny arrow.

@jerem49

Replying to @NUKDDD :

sa ne fonctionne pas non plus ...!

@jerem49

Replying to @jerem49 :

quel matière utilisez vous ?

@ksk4uever

I tried printing the base 2 times and both times it failed at the same spot

The designer has replied

@NUKDDD

Hey, so sorry that it failed on you twice, I think it's an issue with the location of the seam. I've updated the print profiles with the main handle body in it so the seam is at a different spot. I've also uploaded a print profile with just the main body. But that's a really strange blob, almost as if it's extruding too much at the start of each layer and it probably doesn't matter for other areas but it'd really affect a tight corner. Maybe do a flow rate calibration?

(Edited)

@ksk4uever

Replying to @NUKDDD :

Thanks for the quick response. I'll give it one more shot. Cheers

@ksk4uever

Replying to @NUKDDD :

I ran my flow calibrations and then print the handle body with separate print profile and worked perfectly. Thanks again

@Slixxer

I print it with Gold Silk Pla and it doesnt work but with Basic Pla its work just fine. My Son loves it. Thank you

The designer has replied

@NUKDDD

it’s made with small children in mind 😊I’m happy to hear that it brought joy to your son

@AstraCD

Print Profile

Everything you need brim on main handle 0.2mm layer, 2 walls, 6-15% infill

Great toy for kids. Works great! TIP for those that say it doesn't work. You need to face teeth on pulling string towards the arrow.

The designer has replied

@NUKDDD

thanks for the rating and helpful tip! that fudge looks pretty good in blue too. ☺️

@mikeigarcia

Print Profile

Everything you need brim on main handle 0.2mm layer, 2 walls, 6-15% infill

Great toy. My 3 year old loves it. Pull handle is a little hard to grab.

The designer has replied

@NUKDDD

I’ll have an updated version of the stick up soon.

(Edited)

@NUKDDD

annnnd it's up😀 try it out!

@Danny92

Print Profile

Everything you need brim on main handle 0.2mm layer, 2 walls, 6-15% infill

the Boys love it!

@NeoKoiPrints

Print Profile

Everything you need brim on main handle 0.2mm layer, 2 walls, 6-15% infill

base failed

The designer has replied

@NUKDDD

looking at how the brim popped up with it, your build plate isn’t clean at that spot or your bed temp is too low. make sure you didn’t accidentally use the cool plate setting for your texture plate.