Cable Winder Organizer Management V2
Copyright Claim
Cable Winder Organizer Management V2
Boost
120
241
41
Print Profile(4)
0.2mm layer, 3 walls, 10% infill
Designer
33 min
1 plate
6mm Wire
Designer
34 min
1 plate
With holes
Designer
34 min
1 plate
PRINT 3 AT ONCE
1.4 h
1 plate
Boost
120
241
41
2
258
186
Released
Description
It is recommended to print this in TPU.
PLA should also work but is not equally flexible.
Clean the target area with IPA or other cleaners before appling the 3M tape.
I would like to improve the model and your feedback is required.
Happy printing!
Comment & Rating (41)
All
Print Profile
6mm Wire
Excellent model, the wife loves it on her mixer.
The designer has replied
1
Reply
nice looks like it is a part of the mixer. hope you used a good 3M tape.
0
Reply
Print Profile
0.2mm layer, 3 walls, 10% infill
printed well looks nice. however cord clip is a little tight for plenty of the applications I would use. I’d reccomend either making it bigger or MAYBE doing TPU.
The designer has replied
0
Reply
Thankyou for your comment. Yes the first line in the description mentions that it is recommended to print with TPU.
Did you print the 6mm wire version?
What is your wire diameter? I can make another version.
0
Reply
Replying to @CherrysC
my apologies I guess my eyes glazed over that description portion. my Mixer cord should be the same. I used micrometers it’s a lil over 6mm. the PLA is definitely to stiff. I tried but it would damage the cord. I will reprint in TPU and see how it goes. thank you
(Edited)1
Reply
Print Profile
6mm Wire
This 6mm version worked well for my thicker stand mixer wire. I am able to stick it on to the mixer and get the cord in and out nicely. I think a good upgrade would be to make the base a bit thicker and then inset where a command strip (double sided sticky strip) might go. That would make it a bit more asthetic because there would be less gap and less strip visible.
The designer has replied
0
Reply
yea good thinking. this can be done but then the issue would be the thickness of the 3m tape. some are thicker and some are very slim.
0
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 10% infill
nice
The designer has replied
0
Reply
Nice print.
0
Reply
Print Profile
0.2mm layer, 3 walls, 10% infill
The holder printed well and it is big enough to hide a standard 3M command strip. However, the opening in the wire catch was too small for my Kitchen Aid mixers wire. I printed in PLA not TPU, but even with a lot of pressure it would not get into the opening. Perhaps if it were thinner even with PLA it would be be more flexible.
I chose this particular design since the photo showed it with a similar mixer. Photos show me trying to get the cord (6mm diameter) from my mixer to sit in the opening
The designer has replied
0
Reply
Hmmm good to know. I uploaded a version for thicker wire. 6mm should fit in this one.
0
Reply
Print Profile
6mm Wire
printed in TPU. came out fantastic.
0
Reply
Print Profile
0.2mm layer, 3 walls, 10% infill
Could do with holes for fixing, added myself. printed cleanly.
The designer has replied
0
Reply
Hi,
You mean like fixing it to a wall?
I can add a version with holes.
0
Reply
exactlt that, sorry wasnt implying a bad design just not exact for my use. thanks
(Edited)0
Reply
Replying to @user_1649520657
I have uploaded a version with 3mm holes. Hope it works for you.
0
Reply
Print Profile
6mm Wire
stuck these on all the kitchen appliances
The designer has replied
1
Reply
good job
0
Reply
Print Profile
With holes
Nice Idea!
The designer has replied
1
Reply
thanks
0
Reply
Print Profile
0.2mm layer, 3 walls, 10% infill
very clean and smooth print.
The designer has replied
1
Reply
thanks
0
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-NoDerivativesRelated Models
© 2024 MakerWorld