Hogwarts Houses Lightbox by Valeria Momo

Valeria Momo

Art>Signs & Logos

GIF

Print Profile(3)

All

P1S

P1P

X1 Carbon

X1E

V1 (AMS ready)

Designer

5.5 h

2 plates

4.3(6)

0.2mm layer, 2 walls, 15% infill

6.2 h

2 plates

5.0(2)

Less print time, Stronger walls

4.3 h

2 plates

Boost

195

310

291

Released

Description

The BambuStudio AMS ready print profile is loaded in the "raw file" section. If you print the profile I would be happy if you uploaded it as a new print profile.

Harry Potter Lightbox, It has 2 holes on the back to hang it on the wall.
Dimensions: 22 * 23 * 3 cm, check my Harry Potter Collection!

If you like lightboxes, try my collection! LightBox | Collection - MakerWorld

I recommend using 5v LEDs and a simple switch. AMS recommended, No supports required.

Lightbox Desk Stand

If you want to hang the lightbox on your desk or shelf, try my Lightbox Desk Stand.

Commercial license

Do you want to sell prints of this model? You can purchase commercial licensing for this model by joining the Commercial License in my Patreon.

Comment & Rating (23)

@Codyinbody3

Print Profile

V1 (AMS ready)

I’m giving this 3 stars based on the quality of the model. I make a ton of lightboxes and none of the ones I make are this weak and thin. If you grab it too hard it’ll break and it makes it even tougher to put the backplate on where the top edges curl around. It’s a very thin model, top, bottom, backplate and sides. I do however like the idea of this model. just needs to be thicker/stronger.

The designer has replied

@ValeriaMomo

I'm so sorry! my lightboxes are all this thickness, because at the end they have to be hung on the wall and never touched again. I'm sorry you don't like them.

@Codyinbody3

Replying to @ValeriaMomo :

Don't be sorry! 3 stars doesn't mean its bad. 3 stars is for average. There was only one downside to me personally and everyone has their own preferences. I sell a lot of my lamps and ship them across the US so mine have to be a little tougher just in case. Still love the actual image though. I'm a big Harry Potter fan!

@ValeriaMomo

Replying to @Codyinbody3 :

oh, yes, if you need to ship the lightbox, it's better to have more thickness 😊😊😊 mumble... maybe I can edit the model and add another print profile... mumble mumble.... thanks for your feedback 🥰

(Edited)

@StuN22

Boosted

Thankyou for uploading this file! My daughter loves it! Printed with the V1 (AMS ready) profile using one AMS... What a pita! but I got through it! One thing I noticed (after starting the print of the base) is the print time seemed very high for simple walls.. looked through the preview and noticed there are a lot of small sections that it has to print within the walls which is causing the print time to be so high, so I checked the line widths and dropped them to .4... This gives 4 easy straight walls all the way round and reduces print time dramatically. Might be worth just adjusting that in your print profile? The only other thing I did was to put a couple of layers of white into the base so its a more reflective backing when the light go in it So again, No issues.. Just a couple things that could make it a tiny bit better Thankyou!

The designer has replied

@ValeriaMomo

you can add your print profile to the model if you want 😊

@StuN22

Boosted

Replying to @ValeriaMomo :

Thanks for your reply! I've now uploaded my print profile

@photosbyd386

Model printed flawlessly. Great print quality.

The designer has replied

@ValeriaMomo

super 🥰🥰🥰

@dwjensen

How do you do this with only 1 AMS?

The designer has replied

@ValeriaMomo

I use to do manual changes...the colored layers are only 4 (3 layers full colored and 1 fully White). It's a little bit boring but It works

@u.yilmaz91

Replying to @ValeriaMomo :

How did you pause the print and changed filaments mid layer? I see an option to change them at layer changes but I couldn't find an option to do in the same layer. Could you tell me how you set it up on the studio?

@photosbyd386

Print Profile

V1 (AMS ready)

Support Issue:auto or manual supports are needed or the print will wobble on the last 1/2 inch of the print causing it to fail.

The designer has replied

@ValeriaMomo

Hi, I didn't understand what problem you had. Can you give me some more guidance? Thank you

@photosbyd386

the very top of the print would move back and forth when being printed. this movement caused shifted layers.

(Edited)