Balloon Dog by steve_82

steve_82

Household>Decor

Print Profile(1)

All

P1P

P1S

X1 Carbon

X1E

Improved Overhang Quality 0.2mm layer, 2 walls, 15% infill

Designer

2.6 h

1 plate

4.8(38)

Boost

390

481

813

684

Released

Description

A cute balloon dog :)

The profile is set to print at different speed especially for the tail and the nose area.

Enjoy

UPDATE

Added a profile for better overhang supports, especially for underbelly and face. Obviously the supports will be a bit harder to remove but hey you can't always get what you want :)

I've canceled the two other profiles (tree support and fuzzy skin) until I got the same overhang results, so stay tuned!

TIP

In case you print with dark filaments, especially with matte finish, it's possible you'll have some white spots like these, after removing the supports:

If so just use a butane torch and pass the flame rapidly on these zones and you'll have the natural color again:

Comment & Rating (76)

@prhodesj

can anyone help me improve the top surfaces and the underbelly. printing on p1s with tree supports

The designer has replied

@steve_82

I’m working on another profile that improve the underbelly. The top is due to the curve and the layer height, I don’t think there’s much to do but I’ll try

@steve_82

Way better with this settings. I’ll upload it asap

@prhodesj

Replying to @steve_82 :

Brilliant thanks. I managed to get the top surface way better by using variable layer heights. After doing some research I read that sagging on an overhang (even with supports) can be improved by increasing fan speeds (for extra cooling) during overhangs, increasing number of walls, printing inside walls before outer walls and even lower nozzle temp slightly for overhangs. Hope this helps and look forward to seeing your improvements.

@yerden.bitme

I tested the colors of my paints that I haven't used yet, thx for the model (better than painting a plastic spoon)

@Mitch23

Print Profile

0.2mm layer, 2 walls, 15% infill

My family absolutely loves this print. It looks awesome and printed very easily. As others have noted, there were some issues with the surface finish, especially where the supports touched the print you can see in my photos. However, despite this, when it’s displayed on a shelf, you can’t even notice it and I still highly recommend the print. I did notice that there is another profile that was posted that supposed to help with this issue. I have to give that a try.

The designer has replied

@steve_82

Thank you for your comment! Wonderful colors. For the support defects you should definitely try the other profile :)

@furiyh

Print Profile

0.2mm layer, 2 walls, 15% infill

Nice print

The designer has replied

@steve_82

Glad you liked it :)

@user_550034803

Print Profile

Improved Overhang Quality 0.2mm layer, 2 walls, 15% infill

very well made

@rezalty

Print Profile

Improved Overhang Quality 0.2mm layer, 2 walls, 15% infill

scaled it down to do a variable layer test before scaling it up ;)

@wingedpower

Print Profile

0.2mm layer, 2 walls, 15% infill

this balloon dog printed out very well. the design itself is perfectly fine. for me, I had some issues with surface quality where the support material interfaced with the undersides in the first try. the second attempt, I used PETG(overture PETG clear) as the main print material and PLA(Bambu Labs basic white) as the interface material, 0.00 z distance, normal supports. printed very nicely. Infill made it look like cracked ice. might try again with no infill?

@user_1754468547

Print Profile

Improved Overhang Quality 0.2mm layer, 2 walls, 15% infill

supports were difficult to remove but otherwise good print

@Cepheo.

Boosted

impresión sencilla, rápida y muy chula. los soportes son un poco difíciles de retirar, igual hubiera sido mejor los orgánicos. no obstante gracias por compartirlo con la comunidad.

(Edited)

@Sahar

Print Profile

Improved Overhang Quality 0.2mm layer, 2 walls, 15% infill

(Edited)

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Print Profile(1)

Description

Comment & Rating (76)

License

Related Models

Balloon keychain

Balloon Dog Voronoi

Dachshund (flexi-series)

Inflatable Benchy