Assemble succulents|拼装多肉

Try growing 3D printed plants in your office or home. Give as a gift to family and friends. Bringing a touch of spring!

尝试在您的办公室与家里养殖3d打印的植物吧，作为礼物送给家人与朋友，带来一丝春日的气息！

Contains a cute cactus and a clump plant assembled model. No ams system, no support, no glue, just splicing! Some details can be flexibly assembled and changed.

包含一颗可爱的仙人掌与一颗丛生多肉的拼装模型。无需ams系统，无需支撑，无需胶水，完全依靠拼接！部分细节可以灵活的拼装改变。

• The flowerpot is designed with holes so that real succulents can be planted.
• 花盆设计了孔洞，也可以种植正真的多肉植物。

• The connection between the soil and the flowerpot uses elastic buckle designs on all sides. When the 3D printed soil is not loaded, it will not affect the cultivation of real succulents. (Ignore the soil color in this photo)
• 土壤与花盆的连接，四面使用弹性的卡扣设计，不装入3d打印的土壤时亦不影响养真正的多肉。（忽略这张照片的土壤颜色）

• The connection between soil and plants uses buckles or threaded connections. You can assemble any plants on top. It should be noted that the threads are placed vertically for printing convenience. The strength is limited and cannot be subjected to excessive force.
• 土壤与植物的连接使用卡扣或者螺纹连接，理论上你可以拼装任意的植物在上面。需要注意，螺纹为了方便打印是竖着摆放的，强度有限，不能受过大的力。

• The cactus and the clump plant main body are fixed using the screws mentioned above.
• 仙人掌与丛生多肉的主体都使用上面提到的螺丝固定。

• The decorative cactus flowers are also installed using small screws. The screws and flowers are printed separately. After printing, assemble them together.
• 仙人掌的装饰花朵也使用小螺丝安装，螺丝与花朵是分开打印的，打印完再组装到一起。

• The red core at the top of the cactus is actually a screw. It is printed upside down. Flowers used to secure petitions. There are also limited holes between the flowers and the core.
• 仙人掌最上面的红色花芯其实是螺丝，是倒过来打印的，用来固定上方的花朵。花朵与花芯之间也有限位的孔。

• The connection between the main trunk and branches of the clump plant relies on buckles. Use the same clips for the branches and flower cores above. You can play as many sections as you want.
• 丛生多肉的主枝干与树枝之间的连接依靠卡扣，树枝与上面的花芯使用同样的卡扣，想拼几节都可以。

• In order to avoid supporting the printing, a small buckle is used between the branches and leaves. Just be careful when installing here.
• 树枝与树叶之间为了免支撑打印，利用了一个很小的卡扣，这里安装时小心一点就好。

• On top of the 3D printed soil, there are fake stones directly connected by threads, and vines and flowers connected by buckles. Can be freely matched.
• 3d打印土壤之上有直接通过螺纹连接的假石头，与使用卡扣连接的藤曼与花朵，可以自由搭配。