3D model description
AdeleX-10
Small but smart FPV 3D printed VTOL. Super compact, durable and well-designed aircraft.
Flight video
https://youtu.be/GPbEE1ueIIQ?si=tlknNFHe3-9kqIAR
Full manual:
https://adelaero.ru/files/files/adelex-10.manualen.pdf
RC Groups thread:
https://www.rcgroups.com/forums/showthread.php?4541199-VTOL-AdeleX-10-1000-mm-wing-span
Basic characteristics:
Empty weight (without battery): 850 g
Normal take-off weight: 1300 g
Wingspan: 1000 mm
Wing area: 12.5 sq. dm
Wing load: 105 g/sq. dm
Cruising speed: 70 km/h
Stall speed: 50 km/h
Maximum speed: 150 km/h
Maximum wind speed at the ground during takeoff: 7 m/s
Power at NTOW:
hovering: 370 W
cruise mode: 130 W
Cruising range, at a consumption of 4500 mAh (6S): 35-40 km
Ceiling in airplane mode, not less than: 2000 m
Operating temperature range: -15 +35 degrees C
Flight controller software: Ardupilot, INAV
Recommended Electronics:
Airplane:
- Pusher motor (1 pcs) : Motor EMax 2807 1300kv,
ESC 6s 30A, propeller Gemfan 7042.
- Lifting motors (4 pcs): Motor 2004 EMax 1600 kv,
Gemfan 5126-2 propeller.
ESC 4in1 6S, no less than 30A per channel,
Servos: GH-S37D (EMax Es9051) 4pcs.
Batteries: Li-Ion 6s1p 21700 with a current output of at least 30A.
Flight controller: Matek H743, SpeedyBee F405 wing.
Airspeed sensor: Matek ASPD-4525.
Pan&Tilt:
Tilt servo: GH-S37D (EMax Es9051)- 1 pcs.
Rotation servo: DM-s0090d (270 degrees)- 1 pcs.
FPV video system: DJI, Walksnail Avatar.
Radio control system: TBS Crossfire, ELRS.
Cooling fan: 5V 3010
3D printing settings
3D printed FFF model
Parts made of thin-walled ABS (PLA+, PETG), body, stabilizer and wings.
Profile T used (Thin wall).
Dense parts made of ABS (PLA+, PETG) with filling. These are power elements: motor mounts, racks, suspension.
Profile S used (Solid).
Profile T (Thin wall).
Filament - ABS / PLA+
Wall Count - 1
Bottom Layers - 2
Top Layers - 2
Layer height - 0.2mm
Wall thickness - 0.4mm
Infill Line Thickness - 0.25mm
% of Infill - 4%
Infill Type - gyroid / grid
Supports - none
Profile S (Solid).
Filament - ABS / PLA+
Wall Count - 2
Bottom Layers - 2
Top Layers - 3
Layer height - 0.2mm
Wall thickness - 0.4mm
Infill Line Thickness - 0.25mm
% of Infill - 10%
Infill Type - gyroid / grid
Supports - none
Each printer is individual and may require more precise selection of parameters for the best print quality.
If the table adhesion is poor, it is recommended to use printing adhesive or include a border.
ABS should definitely be printed at a high hotend temperature (more than 275 degrees) and a well-heated chamber (table 100 degrees).
Airflow should be turned on to print bridges. For general perimeters, it should be such that the layers have time to harden but not cool before laying a new layer.
ABS-6 plastic from HTP (High Tech Plast) has proven itself to be excellent.
For PLA+ 240 and 60 degrees respectively, no camera is required.
It is not recommended to use plastic PLA+ from other companies other than ESUN.