说明

来自崩坏星穹铁道的王下一桶，被做成了可动3D打印模型。

改模：bilibili@粮亦丰
要求：转载或使用必须表明出处，小批量生产售卖和改模完全可以，但必须标注模型来源，以保持其开放性。

文件内容：桶身、桶盖、四肢、发饰、卡扣、底座部件、可更换手、安装工具（扳手，必要的）

除了打印件以外的零件需求：

通用：3*12螺丝4个、3*5螺丝5个、直径6mm高3mm强磁6个、直径3mm高5mm强磁6个（可动手）、50*50*1方铁片（底座）、4*100mm不锈钢轴（底座）
3mm轴四肢：3*15螺丝、3*10螺丝
2mm轴四肢：2*10钢轴、2*15钢轴

后续可能会更新，以b站为主。

安装指南：

（1）按需打印所有零件，注意四肢只提供了单边模型，需要复制加镜像，卡扣打印4个。请合理设置支撑。

（2）根据选择的版本将四肢先拼好，（手臂根+手臂+小臂，可更换手要使用专用的小臂）（大腿根+大腿+小腿）

（3）将四个3*12mm螺丝从小端完全旋入提供的卡扣中备用。

（4）把腿部零件塞到桶上预留的圆洞里，使用专用工具抓住六角卡扣，把螺丝旋进去，固定双腿。

（5）把手部零件用类似上述步骤的方式固定到桶两侧，注意这次是卡扣不动手部零件转。

（6）用3*5螺丝固定流萤同款发饰。

（7）将6mm直径的磁铁安装在桶和桶盖上，注意安装方向。

（8）安装底座，轴的长度可以按需修改，塞入桶的下面。

（9）可动手需要将直径3mm高5mm的磁铁塞到相应零件里，之后手部就可以更换或旋转了。

不是很有难度的安装，只要零件合格就很轻松。

有问题可以去b站找原视频：

English：This is translated using AI, there may be errors.

Description:

Lordly Trashcan from Honkai: Star Rail.

Model: bilibili@粮亦丰

Requirements: Reproduction or use must indicate the source.

File contents: the body, the lid, four limbs, hair accessories, buckles, base components, interchangeable hands, assembly tools (wrench, as needed)

Parts required other than printed parts:

General: 4 x 3*12 screws, 5 x 3*5 screws, 6 x magnets with a diameter of 6mm and a height of 3mm, 6 x magnets with a diameter of 3mm and a height of 5mm (for poseable hands), 50*50*1mm square iron piece (base), 4*100mm stainless steel shaft (base)

3mm shaft: 3*15 screws, 3*10 screws

2mm shaft: 2*15 steel shaft, 2*10 steel shaft

Assembly guide:

(1) Print all parts as needed, pay attention that only one side model is provided for the limbs, which need to be duplicated and mirrored, and print 4 buckles. Please set up supports reasonably.

(2) Assemble the limbs according to the selected version first (arm root + arm + forearm, use the dedicated forearm for interchangeable hands) (thigh root + thigh + calf)

(3) Fully screw the four 3*12mm screws into the provided buckle from the small end for later use.

(4) Insert the leg parts into the circular holes reserved on the barrel, use the dedicated tool to grip the hexagonal buckle, screw in the screws to secure the legs.

(5) Secure the hand parts to the sides of the barrel using a similar method as above, this time the buckle does not move the hand parts.

(6) Secure the firefly-style hair accessory using 3*5 screws.

(7) Install the 6mm diameter magnets on the barrel and barrel lid, paying attention to the installation direction.

(8) Install the base, the length of the shaft can be modified as needed, and insert it under the barrel.

(9) For poseable hands, insert the 3mm diameter, 5mm high magnets into the corresponding parts, then the hand parts can be replaced or rotated.

The installation is not very difficult, as long as the parts are qualified, it should be fairly easy.